Guía de instalación de HEX ezCAN PURE

Optional Plug & Play Input Harness - CFMoto 001

This is a step-by-step guide to installing an optional HEX ezCAN PURE plug-&-play input harness on CFMoto 450 MT models.

CFMoto 001 optional plug & play input harness packaging:

Optional plug & play harnesses are currently available for the following CFMoto motorcycles:

  • 450 MT models (2024 onward) 
  • 1x optional plug-&-play input harness for CFMoto 450 MT
  • 1x combined high beam/horn trigger harness with blue and green wires
Reproducir vídeo

Paso 1

Lea la guía de instalación genérica de HEX ezCAN PURE.

The generic HEX ezCAN PURE installation guide contains all the general procedures you need to install a HEX ezCAN PURE on your CFMoto 450.

Si tiene previsto instalar un arnés de entrada HEX plug-&-play opcional en lugar del arnés de entrada genérico incluido con el HEX ezCAN PURE, lea las instrucciones que figuran a continuación junto con la guía de instalación genérica del HEX ezCAN PURE.

Guía de instalación de HEX ezCAN PURE

Paso 2

Exponer los puntos de conexión necesarios

IMPORTANT: All disassembly and reassembly instructions on this page are to be regarded as a guide only. For detailed instructions, refer to your motorcycle’s service or workshop manual as appropriate.

Asegúrese de que todos los puntos de conexión de entrada de señal sean fácilmente accesibles siguiendo los pasos que se indican a continuación:

  1. Retire el asiento.
    • The battery is located under the rider’s potion of the seat (red arrow, right).
  1. Remove the left- and right-side fairing panels as follows:
    • Remove the hex-head screws (red arrows, left).
    • Remove the Phillips-head screws (green arrows, left). The lower Phillips-head screw is located on the reverse side of the painted panel, forward of the radiator.
    • Gently pull the painted panels away from the motorcycle, starting at the bottom of each panel and working your way upward toward the
      turn signals.
  1. Remove the left-side and right-side inner infill panels located forward of the radiator, as follows:
    • Remove the panel pin (green arrow, right).
    • Remove the three screws (red arrows, right).
  1. Remove the two hex-head screws at the lower left and lower right corners of the protective radiator shroud (red arrow, left).
  1. Remove the left-side fairing support panel as follows:
    • Displace the turn-signal harness JWPF plug from its securing clip, and disconnect the male and female halves of the plug (green arrow, right).
    • Remove the hex-head screws (red arrows, right).
  1. Remove the right-side fairing support panel as follows:
    • Displace the T-box (highlighted by the white star, left) and temporarily store it out of the way of the work area.
    • Remove the hex-head screws from the same locations as on the left side panel.
  1. Remove the hex-head screws at the inside lower edges of the left-side and right-side fairing support panels (red arrow, right).
  1. Remove the hex-head screws securing the rear ends of the left and right fuel tank trim panels (red arrows, left).
  1. Remove the three hex-head screws securing the fuel filler cap (red arrows, right).
  2. Remove the two hex-head screws securing the upper rear edges of the left and right fuel tank trim panels (red arrows, right).
  3. Remove the fuel filler cap trim panel.
  1. Remove the hex-head screws securing the upper edges of the left and right fuel tank trim panels (red arrows, left).
  2. Remove the left and right fuel tank trim panels by gently pulling them in an upward direction.
  1. The wiring harness connectors for the rear turn signals and tail light are located in the compartment behind the rear portion of the seat, in front of the tail light (red arrow, right).
    • The wiring harness connector for the tail light is a white, flat, 3-pin connector.
    • The wiring harness connectors for the turn signals are bullet-type connectors.
  1. The white 4-pin headlight connector is located underneath the headlight mounting bracket, (in the picture at left, the female 4-pin wiring harness connector is disconnected from the male 4-pin headlight connector). The connector can be accessed by reaching through the black plastic fairing support bracket.

Paso 3

Decida la ubicación del HEX ezCAN

When installing a HEX ezCAN PURE on the CFMoto 450 MT, we recommend that you install the main body under the seat, near the battery.

Nuestra experiencia nos ha demostrado que esta ubicación ofrece la mejor combinación entre la colocación del conector de entrada, la holgura del cable de la batería, la facilidad de acceso al puerto USB y al LED de estado, y la protección contra daños.

Paso 4

Connect the Optional Plug & Play Input Harness to the HEX ezCAN PURE

Conecte el conector JWPF macho de 6 pines del arnés de entrada plug-and-play opcional al conector JWPF hembra de 6 pines del HEX ezCAN PURE (abajo).

Paso 5

Connect the Optional Plug & Play Harness to the Motorcycle

En primer lugar, apague el interruptor de encendido de la motocicleta.

Next, connect the input connectors on the optional plug & play harness to the motorcycle as follows:

Divisor de luz larga (derecha):

  1. Disconnect the motorcycle’s male and female 4-pin headlight connectors located under the left-side front fairing panel.
  2. Connect the female connector on the HEX high-beam splitter to the male wiring harness plug on the motorcycle.
  3. Conecte el conector macho del divisor de luces largas HEX al conector hembra del mazo de cables de la motocicleta.
  4. Vuelva a conectar con cuidado el cable azul del disparador al HEX ezCAN PURE siguiendo el recorrido del mazo de cables y los tubos del bastidor existentes.

Separador de luces traseras (izquierda):

  1. Disconnect the motorcycle’s white male and female flat 3-pin connectors located in front of the tail light.
  2. Connect the female connector on the HEX tail light splitter to the male wiring harness plug on the motorcycle.
  3. Connect the male connector on the HEX tail light splitter to the female wiring harness plug on the motorcycle.
  4. Carefully route the tail light trigger wires back to the HEX ezCAN PURE along existing wiring harness runs and frame tubes.

Divisores de INTERMITENTES:

On the CFMoto 450 MT:

  • The factory left-side rear turn signal bullet connectors have orange and green with light green tracer wires on the wiring harness sides of the connectors, and orange and green wires on the light source sides of the connectors.
  • The factory right-side rear turn signal bullet connectors have sky blue and green with light green tracer wires on the wiring harness sides of the connectors, and sky blue and green wires on the light source sides of the connectors.


Conecte y dirija los cables del divisor de señales de giro de la siguiente manera:

  1. For the left rear turn signal, connect the HEX bullet-connector turn signal splitter with black wire between the bullet connectors with orange wires.
  2. For the right rear turn signal, connect the HEX bullet-connector turn signal splitter with brown wire between the bullet connectors with sky blue wires.
  3. Dirija con cuidado los cables del interruptor de los intermitentes hacia el HEX ezCAN PURE siguiendo el recorrido del mazo de cables y los tubos del bastidor.

Divisor HORN:

  1. Connect the male single-pin connector on the green  horn trigger wire (red arrow, below) to the female horn trigger connector on the main body of the HEX ezCAN.
  1. Remove the spade terminal with light green wire from the factory horn (below).
  1. Connect the ezCAN horn splitter’s male+female spade terminal to the exposed male terminal on the horn (below).
  1. Conecte el terminal hembra en forma de pala desconectado al terminal macho expuesto en el divisor de bocina (abajo).
  1. Vuelva a conectar con cuidado el cable del divisor de bocina al HEX ezCAN PURE siguiendo el recorrido del mazo de cables y los tubos del bastidor existentes.

Paso 6

Reassemble the Motorcycle

The reassembly procedure is the reverse of disassembly.

Paso 7

Configure los valores de inversión de entrada y voltaje umbral.

Para garantizar que el HEX ezCAN PURE ofrezca el máximo rendimiento, ajuste sus entradas de control de la siguiente manera:

  1. Set the input inversion settings and threshold voltage values as seen in Step 2C of the HEX ezCAN PURE Software Download & Configuration Guide.
  2. Si los valores de voltaje umbral indicados en la página anterior no proporcionan un rendimiento constante, ajuste los valores tal y como se muestra en la sección «Ajustes de configuración adicionales para HEX ezCAN PURE» del Manual del usuario de HEX ezCAN (descargue el manual aquí).

Paso 8

Continuar con la instalación

Continúe con la instalación de HEX ezCAN PURE desde el paso 8 de la guía de instalación de HEX ezCAN PURE.

¡Atención!

Ahora se le redirigirá a nuestro sitio web principal para que pueda consultar nuestra Política de privacidad.

LLÉVAME ALLÍ

¡Atención!

Ahora se le redirigirá a nuestro sitio web principal para que pueda consultar nuestra información legal.

LLÉVAME ALLÍ

¡Atención!

Ahora se le redirigirá a nuestro sitio web principal para que pueda consultar nuestra información legal.

LLÉVAME ALLÍ